查看“树莓派”的源代码

[[File:Raspberry_Pi_2_Model_B_v1.1_front_angle_new.png|right|link=https://www.raspberrypi.org|Raspberry Pi 2 Model B]]

==介绍==
树莓派是一款价格低廉、信用卡大小的微型电脑，可以用在多种项目中。它在我们的用户中是最受欢迎的板子之一。
<br>
要在树莓派中运行Domoticz，之前，我们提供了预置'Domoticz'的系统镜像可以直接写入SD卡。<br>
现在，我们不再推荐这种方法了。<br>
<br>
如果你拥有一个全新的树莓派，在安装Domoticz之前，你需要先为你的树莓派安装一个兼容的操作系统。<br>
我们推荐Raspian Jessy Lite，安装很简单，具体请查看[[全新树莓派的第一次设置]]。<br>
<br>
成功安装系统后，请继续进行以下操作。<br>
<br>

==向正在运行的树莓派中安装Domoticz==

#[[在树莓派中安装和运行Domoticz|最简单的方法安装Domoticz： '''sudo curl -L install.domoticz.cn | bash ''']]
#[[在树莓派中安装和运行Domoticz|从源码安装Domoticz]]
<br>

==安装前提：==
*树莓派3B(树莓派1B(+)以及2B、3B+也支持)
*最小4GB大小，class10级别的Micro-SD卡(第一代的Model B需要全尺寸SD卡)
*带读卡器的电脑，用来将操作系统写入SD卡
*显示器和HDMI连接线
*USB接口的键盘和鼠标
*micro USB接口的电源，电压5V (推荐提供2A电流，树莓派3推荐2.5A)
*网线 (或者USB无线网卡) 用来连接到你的网络

(*) 显示器、HDMI线还有键盘跟鼠标都不是必须的，你可以通过电脑来远程控制树莓派，在路由器中找到树莓派的IP，然后说明里的'ifconfig'跳过就可以了。当然，你不能禁用SSH。

<br>

==树莓派附加软件安装==
<br>
成功安装Domoticz后，可以根据以下几个教程继续操作：<br>
<br>

[[设置树莓派看门狗]]<br>
[[监测Domoticz]]<br>
[[在树莓派中安装PPTP-VPN服务器]]<br>
[[为树莓派设置内存分区]]<br>
[[监测内存使用]]<br>
[[NAS监测]]<br>
[[USB设备持久化]]<br>
[[确远程访问安全]]<br>
[[添加Tellstick支持]]
<br>

请至少执行[[USB设备持久化]]。<br>
论坛里有很多新用户在重启后无法正常连接RFXCOM、Z-Wave等。<br>
上面的教程可以避免这个问题。<br>
<br>
==树莓派相关硬件==

[[File:Raspberry_Pi_GPIO_40_pin.png|right|link=http://elinux.org/RPi_Low-level_peripherals#General_Purpose_Input.2FOutput_.28GPIO.29]]
===通用输入/输出(GPIO)===
树莓派1A和1B拥有26针扩展接口<br>
树莓派1A和1B、树莓派2B以及树莓派3B拥有40针扩展接口<br>
Domoticz从1726版本开始支持标准GPIO。<br>
<br>
[https://www.domoticz.cn/wiki/GPIO Domoticz GPIO安装说明]<br>
[https://www.domoticz.cn/forum/viewforum.php?f=32 到Domoticz论坛讨论树莓派GPIO]<br>
<br>
<br>

===PiFace Digital===
[[File:PiFace Digital.png|right|link=http://www.piface.org.uk/products/piface_digital/]]
[http://www.piface.org.uk/products/piface_digital/ PiFace Digital] is designed to plug on to the GPIO of your Raspberry Pi. With PiFace Digital you can detect the state of a switch, for example from a door sensor, a pressure pad or any number of other switch types. You can drive outputs to power motors, actuators, LEDs or anything you can imagine. PiFace Digital has eight digital inputs, eight open-collector outputs, eight LED indicators, two changeover relays and four switches.<br>
The [http://www.piface.org.uk/assets/docs/PiFace-Digital_getting-started.pdf Piface Digital] board is compatible with Raspberry Pi 2 Model B, Raspberry Pi Model B and A (26 pin connector)<br>
The [http://www.piface.org.uk/assets/docs/PiFace-Digital2_getting-started.pdf PiFace Digital 2] board is compatible with Raspberry Pi 2 Model B, Raspberry Pi Model B+ and A+ (40 pin connector)<br>
Support for the PiFace Digital is available in Domoticz release 1045 and onwards.<br>
<br>
[https://www.domoticz.cn/wiki/PiFace Domoticz PiFace Digital installation instruction]<br>
[http://www.domoticz.com/forum/viewtopic.php?f=27&t=624 PiFace Digital Domoticz forum thread]<br>
<br>
<br>

===RaZberry Daughter Card===
[[File:RaZberry.png|right|link=http://razberry.z-wave.me]]
The [http://razberry.z-wave.me RaZberry] is a tiny daughter card that site on top of the Raspberry Pi GPIO connector not blocking the USB boards. It is powered by the Raspberry Pi board with 3.3V  and communicates using TTL signals (RX/TX).<br>
The daughter card hosts a Sigma Designs ZM5202 Z-Wave transceiver module (a so called 5th generation Z-Wave module; old RaZberry hardware was based on ZM3102 module - so called 3rd generation Z-Wave module), an external 32 K SPI flash for network data and a PCBA antenna. Additionally two LEDs are used to indicate certain status of the Z-Wave controller chip.<br>
This board is compatible with Raspberry Pi 3, Raspberry Pi 2 Model B, Raspberry Pi B(+) and is supported by Domoticz.<br>
<br>
NEW - [https://www.domoticz.com/forum/viewtopic.php?f=24&t=10964&start=20#p89074 Domoticz RaZberry installation instruction Raspberry Pi 3] in combination with OpenZwave.
<br>
OLD - [http://www.vesternet.com/resources/application-notes/apnt-85 Domoticz RaZberry installation instruction] in combination with OpenZwave. Please note there is no active support on Domoticz in combination with the Z-way software. 
<br>
<br>

===Pi-mote===
The [https://energenie4u.co.uk/res/pdfs/ENER314%20UM.pdf Pi-mote] control board is is a low cost and a simple wireless controller, dedicated to the Raspberry Pi computer, and Energenie ENER002 RF controlled mains sockets. It is an extremely simple, transmit only, open loop system controlled by six GPIO pins in "out" mode on the Raspberry Pi. It plugs directly into a Raspberry Pi computer, and is powered from the Pi.<br>
<br>
[[Pi-Mote安装说明]]<br>
<br>
<br>

==链接==
[https://www.raspberrypi.org 树莓派基金会官网]<br>
[http://elinux.org/RPi_Low-level_peripherals#General_Purpose_Input.2FOutput_.28GPIO.29 树莓派GPIO细节]<br>
[http://www.piface.org.uk/products/piface_digital/ PiFace Digital官网]<br>
[http://razberry.z-wave.me RaZberry官网]<br>
[https://energenie4u.co.uk Pi-mote官网]<br>

[[Category:Domoticz]]
[[Category:手册]]
[[Category:安装]]
[[Category:Linux]]
[[Category:树莓派]]