在树莓派中安装和运行Domoticz:修订间差异
无编辑摘要 |
|||
(未显示同一用户的7个中间版本) | |||
第17行: | 第17行: | ||
如果你的树莓派中运行的是基于Debian的Linux系统,比如Raspbian和Ubuntu,安装Domoticz非常简单,执行下面的命令即可: | 如果你的树莓派中运行的是基于Debian的Linux系统,比如Raspbian和Ubuntu,安装Domoticz非常简单,执行下面的命令即可: | ||
<code>sudo curl -L install.domoticz. | <code>sudo curl -L install.domoticz.cn | sudo bash</code> | ||
''如果出现以下错误,请安装curl,安装命令:<code>sudo apt-get install curl</code>'' | |||
[[文件:curl_commandnotfound.jpg]] | |||
''最近新装系统的树莓派无法正常运行Domoticz,解决方案:https://www.domoticz.cn/forum/viewtopic.php?f=6&t=121'' | |||
恭喜!安装已经完成了。 | 恭喜!安装已经完成了。 | ||
第23行: | 第30行: | ||
在浏览器中输入你的树莓派的IP与Domoticz默认端口号8080即可访问。在树莓派的浏览器中可以直接输入<code>http://127.0.0.1:8080</code>. | 在浏览器中输入你的树莓派的IP与Domoticz默认端口号8080即可访问。在树莓派的浏览器中可以直接输入<code>http://127.0.0.1:8080</code>. | ||
[注意: 如果安装时遇到证书错误提示,你可以执行<code>sudo curl -L -k install.domoticz. | [注意: 如果安装时遇到证书错误提示,你可以执行<code>sudo curl -L -k install.domoticz.cn | sudo bash</code>,这条命令通过非加密通道下载Domoticz(http而不是https)。 | ||
= Domoticz - 复杂方法(手动安装)= | = Domoticz - 复杂方法(手动安装)= | ||
第126行: | 第132行: | ||
make -j 3 | make -j 3 | ||
= | =设置Domoticz开机自启动(网页升级后也需要)= | ||
sudo cp domoticz.sh /etc/init.d | sudo cp domoticz.sh /etc/init.d | ||
第132行: | 第138行: | ||
sudo update-rc.d domoticz.sh defaults | sudo update-rc.d domoticz.sh defaults | ||
'' | ''编辑启动脚本,修改USERNAME, DAEMON 及 DAEMON_ARGS参数为你自己的设置'' | ||
<code>sudo vi /etc/init.d/domoticz.sh</code> | <code>sudo vi /etc/init.d/domoticz.sh</code> | ||
第140行: | 第146行: | ||
DAEMON_ARGS="-daemon -www 8080" | DAEMON_ARGS="-daemon -www 8080" | ||
如果想用另一个端口访问domoticz,将8080修改为你需要的端口号即可: | |||
DAEMON_ARGS="-daemon -www 8080" | DAEMON_ARGS="-daemon -www 8080" | ||
''' | '''测试Domoticz (确保获取文件所有权!)''' | ||
cd domoticz | cd domoticz | ||
第153行: | 第159行: | ||
sudo service domoticz.sh start | sudo service domoticz.sh start | ||
然后到浏览器中查看Domoticz是否运行正常。 | |||
= | =升级Domoticz= | ||
升级前请一定备份数据库及自定义脚本等内容,升级会导致某些修改丢失。 | |||
=== | ===二进制安装更新=== | ||
使用web界面中的选项升级Domoticz(设置->软件更新) | |||
如果升级失败(例如下载错误),你需要手动升级: | |||
稳定版: | |||
cd domoticz | cd domoticz | ||
./updaterelease | sudo sh ./updaterelease | ||
Beta版: | |||
cd domoticz | cd domoticz | ||
./updatebeta | sudo sh ./updatebeta | ||
=== | 如果以上命令出现连接失败的问题,可以编辑升级脚本,将domoticz.com改为domoticz.cn。 | ||
===源码升级=== | |||
cd domoticz | cd domoticz |
2018年5月15日 (二) 15:15的最新版本
有两种方法将Domoticz安装到你的树莓派,简单方法和复杂方法,两种方法本页均有介绍。
准备(两种方法都需要)
如果你买了个'新鲜'的树莓派,你要确保你树莓派里的系统运行良好。
用"pi"用户登录你的树莓派,打开终端命令行窗口,输入:
sudo raspi-config
Using Raspi-config you should expand the root filesystem, set your timezone, finish (reboot) and login again. You can find various tutorials on how to do this elsewhere on the internet, or you can check out the tutorial on this wiki: 全新树莓派的第一次设置
Domoticz - 简单方法(推荐)
如果你的树莓派中运行的是基于Debian的Linux系统,比如Raspbian和Ubuntu,安装Domoticz非常简单,执行下面的命令即可:
sudo curl -L install.domoticz.cn | sudo bash
如果出现以下错误,请安装curl,安装命令:sudo apt-get install curl
最近新装系统的树莓派无法正常运行Domoticz,解决方案:https://www.domoticz.cn/forum/viewtopic.php?f=6&t=121
恭喜!安装已经完成了。
在浏览器中输入你的树莓派的IP与Domoticz默认端口号8080即可访问。在树莓派的浏览器中可以直接输入http://127.0.0.1:8080
.
[注意: 如果安装时遇到证书错误提示,你可以执行sudo curl -L -k install.domoticz.cn | sudo bash
,这条命令通过非加密通道下载Domoticz(http而不是https)。
Domoticz - 复杂方法(手动安装)
You can also install Domoticz by compiling the source code yourself. The advantage of this is that it should work on most versions of Linux (Debian/Ubuntu tested).
For a manual install see:
Build times reported are when using a Raspberry Pi 3, using "make -j 3"
(Older revisions of the raspberry pi could take up to 10x longer to compile)
You also might need to install GCC 4.6 and compile with this version as 4.9 takes to much memory
Creating a large swap file does not solve the problem, and build with 'make -j 3'
If you are using an old version of the Raspberry Pi, remove the "-j 4" from the make commands!
This will also work for Debian systems, but one these systems you do not need to install the wiringpi library
sudo apt-get install cmake make gcc g++ libssl-dev git curl libcurl4-openssl-dev libusb-dev wiringpi
Change to your source folder (could be your home folder)
Build & Install Boost Libraries
If this is a clean system, continue at Now build and install the Boost library.
[ This should most likely not be needed. The only thing you need to do is to add the flag -DCMAKE_EXE_LINKER_FLAGS=-lboost_atomic to the cmake command when building Domoticz below. I do not own an Raspberry PI so I have not tested it on an Raspberry PI but I have tested it on other ARM computer running debian (sterys) ]
Its recommended that you use the latest Boost libraries - as of 13th November 2016 that is version 1.62.0.
For this we need to compile/install them by issuing the following commands:
These instructions can also be used on a Linux system.
[This first step is necessary because you will get linking errors if you don't remove the old Boost library]
Instructions here are for removing boost 1.55, on your system this might be another version, so adopt these commands to your need. It could also be you never installed boost on your system, do not worry, just execute the commands
sudo apt-get remove libboost-dev libboost-thread-dev libboost-system-dev libboost-atomic-dev libboost-regex-dev sudo apt-get remove libboost-date-time1.55-dev libboost-date-time1.55.0 libboost-atomic1.55.0 libboost-regex1.55.0 libboost-iostreams1.55.1 sudo apt-get remove libboost-iostreams1.55.0 libboost-iostreams1.55.0 libboost-iostreams1.55.0 sudo apt-get remove libboost-serialization1.55-dev libboost-serialization1.55.0 libboost-system1.55-dev sudo apt-get remove libboost-system1.55.0 libboost-thread1.55-dev libboost-thread1.55.0 libboost1.55-dev sudo apt-get autoremove
Now build and install the Boost library.
mkdir boost cd boost wget https://sourceforge.net/projects/boost/files/boost/1.62.0/boost_1_62_0.tar.gz/download tar xvfz download rm download cd boost_1_62_0/ ./bootstrap.sh ./b2 stage threading=multi link=static --with-thread --with-date_time --with-system --with-atomic --with-regex sudo ./b2 install threading=multi link=static --with-thread --with-date_time --with-system --with-atomic --with-regex cd ../../ rm -Rf boost/
Build Support for OpenZWave
If you need support for ZWave, you need to compile open-zwave before compiling domoticz
Make sure to follow the below steps, you will end up with a folder layout like:
- open-zwave-read-only
- dev-domoticz
sudo apt-get install libudev-dev
For the first time, you need to clone the code (copy) from GitHub into your system:
git clone https://github.com/OpenZWave/open-zwave open-zwave-read-only
Refresh the source and build OpenZWave(1m23.057s for initial build (rpi2 3 minutes))
cd open-zwave-read-only git pull make -j 3
go back to the top folder (your Home directory) with:
cd ..
or cd ~
Domoticz Source
For the first time, you need to checkout the source from GitHub onto your system:
git clone https://github.com/domoticz/domoticz.git dev-domoticz
Note building on pi 3 with image september jessy with gcc 4.9, you need bigger swapspace 512 instead of 100 (see https://www.raspberrypi.org/forums/viewtopic.php?f=26&t=46472) or else it will take ages...
Build Domoticz (21m15.899s on a raspberry pi 3 , 35m0.646s on a raspberry pi 2 for initial build)
If you have updated dev-domoticz, the make step will only re-build those files that have been changed - although if a header-file common to a lot of source files has been changed, this will still take a long time
Change to the Domoticz directory, refresh the source and and start building
cd dev-domoticz git pull cmake -DCMAKE_BUILD_TYPE=Release CMakeLists.txt make -j 3
设置Domoticz开机自启动(网页升级后也需要)
sudo cp domoticz.sh /etc/init.d sudo chmod +x /etc/init.d/domoticz.sh sudo update-rc.d domoticz.sh defaults
编辑启动脚本,修改USERNAME, DAEMON 及 DAEMON_ARGS参数为你自己的设置
sudo vi /etc/init.d/domoticz.sh
USERNAME=pi
DAEMON=/home/$USERNAME/domoticz/$NAME
DAEMON_ARGS="-daemon -www 8080"
如果想用另一个端口访问domoticz,将8080修改为你需要的端口号即可:
DAEMON_ARGS="-daemon -www 8080"
测试Domoticz (确保获取文件所有权!)
cd domoticz sudo ./domoticz
Start Domoticz
sudo service domoticz.sh start
然后到浏览器中查看Domoticz是否运行正常。
升级Domoticz
升级前请一定备份数据库及自定义脚本等内容,升级会导致某些修改丢失。
二进制安装更新
使用web界面中的选项升级Domoticz(设置->软件更新)
如果升级失败(例如下载错误),你需要手动升级:
稳定版:
cd domoticz sudo sh ./updaterelease
Beta版:
cd domoticz sudo sh ./updatebeta
如果以上命令出现连接失败的问题,可以编辑升级脚本,将domoticz.com改为domoticz.cn。
源码升级
cd domoticz git pull make -j 4